商品介紹：

·FDJ-120型風動切開鋸適用于風險的作業環境，可在較高溫的環境下作業，無火花，在濕潤的環境中無漏電風險，是一款功能牢靠、安全型及效率極高的抱負風動?xùn)|西之一。廣泛用于采礦、石化、修建等職業。

·使用井下壓風管道體系作為動力源。重量輕，易帶著；構造科學，便于作業。 思禮鎮

·可迅速切開管道、電纜、角鋼、構造鋼、U型鋼、鏈條、錨桿、錨索等。

·錮金屬鋼合金超級鋸條，耐高溫、耐沖突、運用壽數長。十分適用于鋸割不銹鋼、鎳基合金、鐵、銅、鋁、玻璃、塑料、木材等。

技術參數： 

氣動風動切開鋸運用方法：

1、知道所需切開的材料，如有必要可以通過降低空氣壓力來降低鋸片的改變速度。 

2、確保固定了所需切開的材料，防止其移動。

3、氣動空氣馬達時，用手指按壓閥桿，然后初步切開。

4、用鋸的重量來控制切開壓力。對于較軟的材料來說，這么的重量現已滿意。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方法來降低鋸片的改變速度。切開是堅持鋸筆直。鋸片的任何曲解或歪斜都可以降低其運用壽數。（留意：避開切開后可以墜落的碎片。切開即將結束時，切勿使鋸碰到您的身體、工件或鄰近的其它人員。）

5、封閉空氣馬達時，開釋閥桿。

6、下次切開初步前，鋸片有必要堅持運動情況。氣動鋸時，鋸片不能接觸任何表面。 偃師市FDJ-120/礦用防爆切割鋸

7、斷開空氣軟管時，封閉空氣軟管閥。斷開前，先翻開空氣閥給軟管減壓。

8、更換鋸片前，有必要斷開空氣軟管，并推動閥桿以開釋掉馬達內的壓力。

9、順時針改變調整手柄以便開釋鋸片導桿上的張力。然后開釋側面板的鎖以便翻開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。

為了安全作業需要注意一下幾點：

1.用鋸的重量來控制切割的壓力。對于較軟的材料來說，這樣的重量已經足夠。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命

2.關閉啟動馬達時，釋放閥桿。

3.更換鋸片前，務必斷開空氣軟管，并推動閥桿以釋放掉馬達內的壓力。

4.順時針轉動調整手柄以釋放鋸片并將其從據帶導桿上松開。

5.下次切割開始前，鋸片必須保持運動狀態。氣動鋸時，鋸片不能接觸任何表面。

6.了解所需切割材料，如有必要時可通過降低空氣壓力來降低鋸片的速度.

7.確保牢固固定了所需切割的材料，防止其移動。

8.氣動空氣馬達時，用手指按壓閥桿，然后開始切割。

9.斷開空氣軟管時，關閉空氣軟管閥。斷開前，先打開空氣閥給軟管減壓。

 Commodity introduction:
The FDJ-120 type pneumatic cutting saw is suitable for the risk working environment. It can operate in a high temperature environment, no sparks, and no leakage risk in humid environment. It is a reliable, safe and highly efficient aspiration pneumatic thing. It is widely used in mining, petrochemical, construction and other professions.
Use the downhole air pressure pipe system as a power source. The weight is light and easy to be carried; it is scientific and easy to work. Si Li Zhen
The pipeline, cable, angle steel, structural steel, U type steel, chain, bolt, anchor cable and so on can be cut off quickly.
Super - Han metal steel alloy saw blade, high temperature resistance, long life, the use of conflict. It is very suitable for sawing stainless steel, nickel base alloy, iron, copper, aluminum, glass, plastic, wood and so on.


Technical parameters:
Type power consumption cutting width (diameter) blade speed weight
FDJ-120 1kW 0.6 120mm 60m/min 6kg
Pneumatic pneumatic cut saw application method:
1. Knowing the material that needs to be cut, it is necessary to reduce the speed of the saw blade by reducing the pressure of the air.  
2, ensure that the material needed to be cut is fixed to prevent its movement.
3. When pneumatic air motor, press the stem with the finger, and then cut it initially.
4, the cutting pressure is controlled by the weight of the saw. This weight is now satisfactory for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of the saw blade can be reduced by pressure. The incision is to keep the saws straight. Saw any distortion or skew can reduce the use of life. (notice: avoid debris that can fall after a cut. When the cut is about to end, do not make the saw touch your body, the workpiece, or the other people in the neighborhood.
5. When the air motor is closed, the stem is released.
6. Before the next incision, it is necessary to adhere to the movement of the saw blade. The saw blade can't contact any surface when a pneumatic saw. Yanshi city FDJ-120/ mine explosion-proof cutting saw
7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.
8. Before replacing the saw, it is necessary to disconnect the air hose and push the stem to release the pressure of Madane.
9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod.


A few points need to be paid attention to for safe operation.
1. the weight of the saw is used to control the pressure of the cutting. This weight is enough for softer materials. The cutting is to keep the saws straight. Any twist or skew of the sawblade may reduce its service life
2. release the stem when the motor is turned off.
3. before replacing the blade, be sure to disconnect the air hose and push the stem to release the pressure of Madane.
4. clockwise rotation of the handle to release the blade and release it from the guide rod.
5. the saw blade must remain moving before the next cutting begins. The saw blade can't contact any surface when a pneumatic saw.
6. understand the required cutting material and reduce the speed of the saw blade by reducing the air pressure if necessary.
7. ensure that the required cutting material is firmly fixed to prevent its movement.
8. pneumatic motor, press the stem with the finger, then start cutting.
9. when the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.